The MC3487 provides four separate differential line drivers designed to meet the specifications of ANSI TIA/EIA-422-B and ITU Recommendation V.11. Each driver has a ttl compatible buffered input to reduce current and minimize load. The MC3487 is designed for optimum performance when used with the MC3486 four-wire receiver. It comes in a 16-pin dual-in-line package and is powered by a single 5-V power supply
The TPA2000D2 is the third generation 5-V Class d amplifier produced by Texas Instruments. Improvements to the previous generation of devices include: lower supply current, lower noise underside, higher efficiency, four different gain Settings, smaller package, and fewer external components. The most significant advance of the device is its modulation scheme, which allows the amplifier to operate without an output filter.
The N25Q is a high-performance multi-input/output serial flash memory device manufactured using 65nm NOR technology. It features in-place execution (XIP) capabilities, advanced write protection mechanisms, and a high-speed spi compatible bus interface.
The HMC197BE is a low-cost SPDT switch in a 6-pin SOT26 plastic package for general switching applications requiring very low insertion loss and a very small size. The device can control signals from DC to 3 GHz, especially for 900 MHz, 1.8-2.2 GHz, and 2.4 GHz ISM applications with losses of less than 1 dB.
The XRD9826 is a complete linear CIS or CCD sensor signal processor on a single monolithic chip. The XRD9826 includes a high speed 16-bit resolution ADC, a 6-bit Programmable Gain Amplifier with gain adjustment of 1 to 10, and 8-bit programmable input referred offset calibration range of 800mV.
The SC2545 is a high performance dual PWM controller. It is designed to convert a wide ranged input voltage down to two independent output rails. The SC2545 support “peel off ” tracking for the two outputs at start up which means the two outputs ramp up together till the one with lower output level reaching the regulation.
The IR2011 is a high-power, high-speed power MOSFET driver with a separate high-low side reference output channel. A floating channel can be used to drive a high-side configuration of N-channel power mosFETs that operate at up to 200 volts. Proprietary HVIC and latch-immune CMOS technology enable a rugged overall structure.
The BQ26500 is the first advanced gas measurement device in the bqJUNIOR family for handheld applications. It is a high-precision stand-alone single-cell lithium-ion and lithium-POL battery capacity monitoring and reporting device for portable applications with limited space.
The DS2746 provides system-side battery capacity monitoring in cost-sensitive applications. Voltage, bidirectional current, and accumulated current measurement data is provided to the host processor over a 2-wire interface. Offset bias and offset blanking features greatly enhance the accuracy of the coulomb counter.
The SiP21106 BiCMOS 150 mA low noise LDO voltage regulators are the perfect choice for low battery operated low powered applications. An ultra low ground current and low dropout voltage of 135 mV at 150 mA load helps to extend battery life for portable electronics. Systems requiring a quiet voltage source, such as RF applications, will benefit from the SiP21106 low output noise.
The LM337L is an adjustable 3-pin negative voltage regulator capable of supplying 100 mA over a –1.2-V to –37-V output range. The LM337L is easy to use and requires only two external resistors to set the output voltage. Both line and load regulation are better than standard fixed regulators. The LM337L is packaged in a standard, easy-to-use TO-92 transistor package.
The ISL8540 is a step-down DC/DC power switch regulator that accepts 9.0V to 40V inputs and provides 2A output current. The output voltage can be set between 1.21V and 35V via an external voltage divider. The DMOS transistor devices using internal power, typical rDS (ON) 0.19Ω, in order to obtain high efficiency and high speed switch.
The VFC320 monolithic voltage-frequency and frequency-voltage converters provide a simple and low-cost method for converting analog signals into digital pulses. The full range frequency and input voltage are determined by a resistor in series with the -In and two capacitors (one-time timing and input amplifier integration). The other resistor is a non-critical open collector pull-up (fOUT to +VCC). The VFC320 is available in two performance levels. The operating temperature of the VFC320 ranges from -25 ° C to +85 ° C
The MIC4467/8/9 family of four output CMOS buffer/drivers is an expansion from the earlier singleand dual-output drivers, to which they are functionally closely related. Because package pin count permitted it, each driver has been equipped with a dual input logic gate for added flexibility. Placing four high-power drivers in a single package also improves system reliability and reduces total system cost. In some applications, one of these drivers can replace not only two packages of single-input drivers, but some of the associated logic as well
The MAX8677C is an integrated 1-cell Li+ charger and Smart Power Selector with dual (DC and USB) power inputs. It can operate with either separate inputs for USB and AC adapter power, or from a single input that accepts both. All power switches for charging and switching the load between battery and external power are included on-chip. No external MOSFETs are required.
The REG101 is a family of low-noise, low-dropout linear regulators with low ground pin current. Its new DMOS topology provides significant improvement over previous designs, including low dropout voltage (only 60mV typ at full load), and better transient performance.
The TPS6755 is an adjustable inverter dc/dc converter capable of operating from inputs as low as 2.7V. Suitable for board level dc/dc conversion in computer peripherals and battery powered devices requiring high efficiency and low supply current. The TPS6755 is available in an 8-pin DIP or 8-pin SOIC package and operates in the -40° free air temperature range
The LTC4267-3 combines an IEEE 802.3af compatible power supply device (PD) interface with a 300kHz current mode switching regulator to provide a complete power solution for PD applications. Designed to drive a 6V rated N-channel mosFEts in a space-saving low-spec 16-pin SSOP or DFN package, it features programmable slope compensation, soft start and constant frequency operation that minimizes noise even under light loads, and includes an onboard error amplifier and reference voltage that allows for use in isolated and non-isolated configurations.
